Ünver Makina
Products - Edge Banding Machines - BANTMATİK 435 EDGE BANDING MACHINE
Detail Technical Informations Settlement plan Catalog

MACHINE LENGHT 4,3 METERS FROM DOOR TO DOOR. IT HAS PLC CONTROL PANEL AND 5 UNITS. WORKING SPEED IS 12 METER/MINUTE.

 

AIR COMPRESOR WITH AIR DRYER, DUST SUCTION MACHINE AND REGULATOR MUST BE USED FOR MACHINE. START-UP, INSTALLATION AND MAINTENANCE SHOULD BE DONE FROM UNVER WOODWORKING MACHINERY QUALIFIED TECHNICIANS. IF YOU DONT OBEY CONDITIONS, YOUR MACHINE LIFESPAN WILL SHORTEN. IT WILL NOT INCLUDED WARRANTY.

PANEL BOARD

Use fastly with panel board. Pratical and easy to use. Reach all past defect.You can learn total material and pvc band length.

PRE HEATER PROFILE

The front surfaces are heated and dried by resistance heating at 80 degrees to prevent moisture and sweating.

GLUE UNIT 4 liter glue capacity, ready 5-15 minutes. Stiffened and annealed glue roller.Preview glue stcik system. 4 kh bearing, back spring concept.
PRESS UNIT Press roller is adjusted by pressure, it rotates same as a palet speed. There are 3 press roller which is pressure adjusted. Press platform’s back and forward movement calibrated by indicator easily.
BEGINNING-END MILLING

45° angled, pair of linear sled beginning-end milling unit. At 1200 rpm, it cuts beginning-end sensitively with high frequency motors.

ANGLED BOTTOM-TOP MILLING It can cut till 30°, using preview disk bright surfaces can milling without scratch.at 18000 rpm sensitive surfaces can milling with high frequency motors. Band thickness can control 0,4 - 3 mm accurately by indicator. All excelsiors absorbed by dust suction.
CORNER ROUNDING

At 18.000 rpm, pair of motor and four dynamic pneumatic automation systems. Tirim milling system, can choose parpendicular cornered, postforming or cover profils. 0,4 - 3 mm band thickness adjustment calibrated by indicator easily.

R2 SCRAPING

Using preview disk bright surfaces can scraping with radius. 0,4 - 3 mm band thickness adjustment calibrated by indicator easily

CLEANING LIQUID

Glue remnants occur near the band edge. Glue remnant cleaning easily with solvent.

BUFFER UNIT

15 angled, forward-back and down-up polishing motors obtain clean and bright surfaces.

DUST SUCTION

1.200 m3 dust suction fan absorb all pvc excelsiors from pre-milling and bottom-top milling.

TAPPING PALLET M5 thread connected on the 1” strong bridged chain, tapping palet and bearing top wheels, bright materials processing without scratch

1)       TECHNICAL INFORMATIONS

BANTMATİK 435 TR

2)       CONTROL UNIT

PANELBOARD

3)       MAXIMUM PANEL THICKNESS

8 MM / 60 MM.

4)       BAND THICKNESS

0,4 MM / 5 M

5)       MINIMUM PANEL LENGTH

120 MM

6)       MINIMUM PANEL WIDTH

100 MM

7)       GLUE CAPACITY

3 LT / 4 KG

8)       GLUE HEATING TIME

20-25 MINUTE

9)       WORKING SPEED

12 MET/ DAK (M/MIN)

10)   END MILLING CUTTER MOTORS (2 PIECES)

0,37 KW 12.000 R.P.M

11)   BOTTOM-TOP MILLING CUTTER MOTORS (2 PIECES)

0,55 KW 18.000 R.P.M

12)   TRIM  MILLING CUTTER MOTORS (2 PIECES)

0,55 KW 18.000 R.P.M

13)   BUFFER MOTORS (2 PIECES)

0,25 KW / 3.000 R.P.M

14)   DUST SUCTION MOTOR

0,75 KW 1.200 M3

15)   POWER

10 KW

16)   VOLTAGE

380 – 400 V / 50–60 HZ

17)   CURRENT

26 AMPER

18)   WORKING PRESSURE

4/6 BAR

19)   TRANSPORTATION DIMENSIONS LENGHT - WIDTH - HEIGHT

5.1 X 0.75 X 1.5 M

20)   WEIGHT

1.700 ± 30 KG